Top 10 Pi 4 PoE HAT – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. waveshare

#ad

Supports 802.3at PoE Standard with 5V DC/4A High Power Output,with Controllable Brushless Cooling Fan, 2021 New Version Official Raspberry Pi POE+ HAT for Raspberry Pi 4/3B+

#ad
waveshare #ad - Fully isolated switched-mode power supply for better power efficiency. Providing both network connection and power supply for your Raspberry Pi in one cable.

The raspberry pi poe+ hat is a power over Ethernet PoE+ accessory for the Raspberry Pi 3B+/4B. Compared to its predecessor raspberry pi poe hat, implementing the 802. 3af/at standard with 5v dc/4a larger power output, it features better cooling effect, providing enough power for both Raspberry Pi 3B+/4B at max load and other peripherals at the same time. Built-in controllable brushless 25 x 25mm fan delivering 2. 2 cfm for better heat dissipation.
Brandwaveshare #ad
ManufacturerWaveshare #ad
Part NumberBC-Official POE+ HAT for RPi-C

2. GeeekPi

#ad

GeeekPi Raspberry Pi 4 Isolated PoE HAT Support IEEE 802.3af or 802.3at PoE Standard,with Raspberry Pi Cooling Fan 30x30x7mm for Raspberry Pi 4 Model B / 3B+ 3B Plus

#ad
GeeekPi #ad - Input voltage: 37~57v dc, class 2 device;Output voltage: 5V DC/2. 5a;. Standard:ieee 802. 3af-2003 PoE. Cooling: 30mm x 30mm brushless fan; Fully isolated switched-mode power supply.
BrandGeeekPi #ad
ManufacturerGeeekPi #ad
Part NumberEP-0127

3. LoveRPi

#ad

Raspberry Pi PoE+ HAT with Low Profile Heatsink

#ad
LoveRPi #ad - Optimized for remote: power over ethernet provides single cable power and connectivity to the Raspberry Pi 4. Low profile heatsink included: further reduce temperatures by increasing the thermal surface area of the powerful SoC with advanced 3M thermal transfer tape.

With cooler ambient temperatures or low load, the fan will reduce speed for silent operation. Power usb 3. 0 devices: two usb 3. 0 type a ports on the raspberry pi 4 can deliver up to 1A each. Quiet configurable fan: equipped with a powerful 25mm x 25mm brushless fan, the PoE+ HAT can operate up to 50°C ambient temperature with adequate airflow. Remove the blue plastic and adhere the low profile heatsink to the main chip to reduce temperatures and increase speed. 2021 poe+ hat for pi 4: designed for the powerful raspberry pi 4, the raspberry Pi PoE+ HAT delivers up to 20W of power from IEEE 802.

3at poe+ compliant switches so that your Pi 4 never runs out of juice. The original poe hat could not supply enough current for demanding USB 3. 0 devices like backup drives, 4K webcams, and more. Ideal for reducing cable runs, remote sensing and acquisition, acting as access point AP, the PoE+ HAT further expands already incredible capabilities and processing power.
BrandLoveRPi #ad
ManufacturerLoveRPi #ad
Warranty30 Days

4. waveshare

#ad

Isolated, PoE HAT Onboard Cooling Fan and MP8676 Buck Chip, waveshare Power Over Ethernet PoE HAT for Raspberry Pi 4B/3B+, 802.3af/at PoE Network Standard, 5V USB-A&12V Header Outputs

#ad
waveshare #ad - Power over ethernetpoe power over ethernet capability, IEEE 802. 3af/at-compliant power sourcing equipments, providing both network connection and power supply for your Raspberry Pi in one Ethernet cable.

Poe hat isolatedfully isolated switched-mode power supply SMPS. 5v usb-a & 12v header outputs5v usb-a provides up to 4a output max 25w for 12v+5v total output power, While providing stable power for the Raspberry Pi, there's also a USB-A port for powering extra external device. Onboard cooling fan and mp8676 buck chippoe hat with high speed active cooling fan, better heat dissipation, incorporates MP8676 original voltage buck chip, providing up to 4.5a output for raspberry Pi and USB-A port. Poe hat for raspberry pi 4b/3b+standard raspberry pi 40pin gpio header, supports Raspberry Pi 3B+/4B, allows Power Over Ethernet HAT connecting other HATs.
Brandwaveshare #ad
ManufacturerWaveshare #ad
Weight0.12 Pounds

5. UCTRONICS

#ad

Power Over Ethernet PoE Support 802.3af PoE Network Standard, UCTRONICS PoE HAT for Raspberry Pi 4B/3B+, Compatible with Pi 4B / 3B+

#ad
UCTRONICS #ad - Smaller size: 65*44*13mm, save more space for your other hardware, nearly half the official size, can be held in the most case for Raspberry Pi. If used with pi 4, you can search ASIN B07WMNXB4V to get the case with the fan.

Please make sure the adequate air circulation to help it dissipate heat to ensure stable operation. Well-ventilated environment recommended: it’s normal to become hot when the HAT operating. Update: this lastest uc-858 mini poe haT Compatible with 48V non-standard switches so it can supports more brands of switches. Output power: dc 5v 2. 5a max; total power budget: 12. 5w; ieee 802. 3af Compliant. For pi 4 and 3 b+: this poe hat can be used to deliver clean and reliable power to the raspberry pi 3 model B+ and raspberry pi 4 model B not included.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Height0.94 Inches
Length3.1 Inches
Width2.2 Inches
Part NumberU6109

6. Raspberry Pi

#ad

Official Raspberry Pi Power Over Ethernet PoE HAT for Raspberry Pi 3 B+ and 802.3af PoE Network

#ad
Raspberry Pi #ad - Smps: fully isolated Switched-Mode Power Supply with fan for cooling. May be used to power your raspberry pi 3 B+ with an Ethernet cable on a PoE enabled network, eliminating the need for a separate power supply. 802. 3af compliant PoE. Class 2 poe device: 36-57v input, 5v/2. 5a output. This is the updated version, which addresses the current limiting issue found in the original release. This is the 2018 official raspberry pi power over ethernet PoE HAT for the Raspberry Pi 3 Model B+.
BrandRaspberry Pi #ad
ManufacturerRaspberry Pi #ad
Height0.98 Inches
Length2.95 Inches
Weight0.09 Pounds
Width3.15 Inches
Part Numberrb-poehead2
Modelrb-poehead2
Warranty30 Day Parts

7. LoveRPi

#ad

LoveRPi Power-Over-Ethernet PoE HAT for Raspberry Pi 4 Model B and Raspberry Pi 3 Model B+ Compact, Non-Isolated

#ad
LoveRPi #ad - Passive poe" dc 24v or 48v is not standards compliant and may cause damage to equipment. Standards compliant power over ethernet switch required: the network switch or power sourcing equipment pse must be compliant with the IEEE 802. 3af or 802. 3at poe standard, particularly section 33. 4. 1 with regards to PSE electrical isolation of the leads.

Poe switch and raspberry Pi 4 Model B sold separately. Some ubiquiti switches do not provide provide proper isolation so please use the professional version! Built for cluster nodes: simplify cable management and expand your on-premise cloud with POE! Power five, ten, twenty Raspberry Pi 4 Model B boards through a single POE switch. Poe power output must be within the budget of the switch when powering multiple boards. This poe hat was designed to exceed the power delivery standards set by the official Raspberry Pi PoE HAT and other products available on the market. Ventilated case with cooling fan highly recommended: Do not use this product in an enclosed case without active air circulation.

Ultimate power over ethernet hat for raspberry pi 4: deliver clean and reliable power to the latest Pi 4! Power-over-Ethernet is both simple, power efficient, and cost effective compared to having multiple power adapters. Airflow around the hat and Raspberry Pi 4 Model B must be adequate to ensure performance and stable operation. Easy installation and backwards compatible: please remove all non-essential heatsinks including RAM/USB/Ethernet heatsink before seating the HAT! Supports the latest Raspberry Pi 4 as well as the Raspberry Pi 3 Model B+.
BrandLoveRPi #ad
ManufacturerLoveRPi #ad
Part NumberLRP-RPIHAT-POE-RPI4

8. GeeekPi

#ad

GeeekPi Raspberry Pi 4 PoE HAT Support IEEE 802.3af or 802.3at PoE Standard,with Raspberry Pi Cooling Fan 30x30x7mm for Raspberry Pi 4 Model B / 3B+ 3B Plus

#ad
GeeekPi #ad - Compatible with: raspberry pi 4 Model B / Raspberry Pi 3 Model B+. Protection circuitry: transient Overvoltage, Undervoltage Lockout, Thermal Shutdown, Foldback Current Limiting. Built-in 30x30x7mm cooling fan;only support IEEE 802. 3af or 802. 3at poE standard.
BrandGeeekPi #ad
ManufacturerGeeekPi #ad
Part NumberEP-0115

9. UCTRONICS

#ad

UCTRONICS PoE HAT for Raspberry Pi 4, 802.3at Power Over Ethernet Expansion Board for Raspberry Pi 4 B 3 B+, with Cooling Fan

#ad
UCTRONICS #ad - Over-temperature protection: the 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high. Output power: dc 5v 3a max / 12v 2a max via the terminal interface reserved; Total Power Budget: 25W; IEEE 802. 3at Compliant. For pi 4 and 3 b+: this poe hat can be used to deliver clean and reliable power to the raspberry pi 3 model B+ and raspberry pi 4 model B not included. Note: pse power supply equipment is needed to supply PoE signal to the Raspberry Pi, such as a PoE switch or injector.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Part NumberUCT_U6102

10. UCTRONICS

#ad

802.3at Power Over Ethernet Expansion Board for Pi 4 B Board, UCTRONICS PoE HAT for Raspberry Pi 4 with Case, with Cooling Fan

#ad
UCTRONICS #ad - Please contact us if you received wrong pieces, we will send you a new case kit ASAP. Higher output power: dc 5v 3a max / 12v 2a max via on-board terminal block; Total Power Budget: 25W.

Over-temperature protection: The 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high. Well-ventilated case: cut-outs for every port of Pi 4 board and PoE hat, easy to access to all ports as well as supplying well-ventilated environment. Note: pse power supply equipment is needed to supply PoE signal to the Raspberry Pi, such as a PoE switch or injector. Perfect for pi 4: this poe hat can be used with raspberry pi 3 model B+ and Raspberry Pi 4 model B not included.
BrandUCTRONICS #ad
ManufacturerUCTRONICS #ad
Part NumberU610201